In final chapter , we give out the result of our whole system . then discuss the disadvantage of our system and give some new method to improve it 最后一章給出系統的實驗結果,并且討論了目前系統存在的不足之處和改進方法。
Finally , we give out the result of experiment and the analyses of error . the test running result shows that the system reaches the expectant affect and purpose 最后,由系統的軟硬件調試及實驗結果表明,本設計的多功能監控儀性能穩定,各項指標基本達到技術要求。
The third type assesses the cost of the hardware implement and the feasibility . last , we give out the results of visual comparison and quantitative comparison based on some test images 并針對部分典型的測試圖片,以及部分代表性算法,給出了相關視覺比較與數據比較的結果。
The expert thinks , the thing that evaluation wants to do is far more than give out the result is so simple , there is the process that an integration analysis evaluates even before , this process is very tall to professional quality requirement of the person 專家認為,測評所要做的事情遠不止給出結果這么簡單,之前還要有一個綜合分析評估的過程,這個過程對人的專業素質要求很高。
At last we give out the result of plenty of simulation data and real sar data . and we also analyze the performance of the algorithm from the point of view of different velocity , different signal / noise energy ratio , different aotufocus algorithm , different patch size 然后本文給出大量仿真數據和實測數據檢測結果,分別從不同運動目標速度、不同信噪比、不同相位誤差估計算法、不同分塊大小等角度進行檢測性能分析。
This paper introduces an instrument which is applied to measuring the characteristic parameters of light emitting diode ' s or some of other light sources " . relevant theories are verified by this instrument . the principle of this instrument system can be described as follows : it takes photodiode as its detector , and a single - chip mcu named at89c51 is the core processor that manages data acquisition , field control , data communication , etc . pc analyses datas and apply algorithms to get the characteristic parameters of led , and then gives out the results of analyse in proper ways 該儀器系統采用光電二極管作為光電探測傳感器,以at89c51單片機為核心處理器,進行數據采集和現場控制,并通過與pc機發生通信,將數據發回pc機進行進一步的處理, pc可在此基礎上從算法級對二極管特征參數進行分析和運算,并進而以合適的數據表現方式給出分析結果。
The report discusses technical ways to implement digital signature , introduces several representative signature schemes and specifies n - r - q new scheme . in software design , the expression of large integer is defined by a new method based on dsp and large integer operation algorithms are designed according to that . after completing the signature program in assembler by special repertoire of dsp ( tms320c50 ) , we run it on the platform of software simulator and give out the results 針對n - r - qnew數字簽名方案,在軟件設計中,基于dsp對大整數的表示重新進行了的描述,相應設計了大整數的基本運算算法,用dsp ( tms320c50 )的專用指令系統完成了數字簽名軟件的匯編程序設計,并在軟件仿真平臺上對其進行了仿真,通過仿真結果闡述了用dsp實現數字簽名的可行性。